Opening: 9:00-5:00

Custom Dark Maple Hardwood Sports Flooring Company

Custom Dark Maple Hardwood Sports Flooring Company
Custom Dark Maple Hardwood Sports Flooring Company
Custom Dark Maple Hardwood Sports Flooring Company

Custom Dark Maple Hardwood Sports Flooring Company

Inquire

In stock

Dark maple (Acer saccharum) is selected for its tight, uniform grain and high density, typically ranging from 0.70 to 0.75 g/cm³ after kiln drying to 6‑8% moisture content. The wood undergoes a

Share this on:
Custom Dark Maple Hardwood Sports Flooring Company

Custom Dark Maple Hardwood Sports Flooring Company

Custom Dark Maple Hardwood Sports Flooring

Material Overview

Dark maple (Acer saccharum) is selected for its tight, uniform grain and high density, typically ranging from 0.70 to 0.75 g/cm³ after kiln drying to 6‑8% moisture content.

The wood undergoes a steaming process to achieve a deep, consistent amber‑brown tone without surface stains, preserving the natural cellulose structure.

Mechanical Properties

  • Janka hardness: approximately 1450 lbf, providing resistance to indentation from sports equipment.
  • Modulus of elasticity: 1.8–2.0 GPa, contributing to consistent ball rebound.
  • Density: 0.72 g/cm³ average, influencing shock absorption characteristics.

Performance Characteristics for Sports Flooring

When installed over a resilient subfloor, dark maple delivers a vertical deformation of 2.3‑2.8 mm under a 500 N impact, meeting EN 14904 standards for area‑elastic sports surfaces.

The finished surface exhibits a coefficient of friction between 0.55 and 0.65 (dry), balancing slip resistance with allowable lateral foot movement.

Wear resistance is quantified by a Taber abrasion index of ≤80 mg loss after 1000 cycles, ensuring longevity under frequent training and competition.

Customization Options

  • Thickness: 14 mm, 18 mm, or 22 mm solid planks; engineered constructions available upon request.
  • Width: 60 mm, 90 mm, or 120 mm face widths, with optional beveled or square edges.
  • Finish: UV‑cured polyurethane (matte, satin, gloss) or oil‑based penetrating sealers, each with specified VOC limits.
  • Edge profiling: tongue‑and‑groove, click‑lock, or concealed fastening systems.
  • Surface branding: laser‑etched logos or custom graphics integrated into the wear layer without affecting hardness.

Installation Considerations

Acclimatization to site conditions (relative humidity 40‑60%, temperature 18‑24 °C) for a minimum of 72 hours is required before laying.

Subfloor flatness tolerance: ≤3 mm over a 2 m straightedge; any deviation must be corrected with self‑leveling underlayment.

Fastening methods include concealed cleat nails, adhesive‑bonded systems, or mechanical interlocking clips, selected based on subfloor type and expected load cycles.

Typical Applications

The combination of high stiffness and controlled damping makes dark maple suitable for basketball courts where consistent ball bounce and player joint protection are critical.

For volleyball, the surface’s low lateral slip reduces ankle injury risk during rapid lateral movements while still permitting controlled sliding for defensive plays.

Multi‑use facilities benefit from the flooring’s resistance to point loads from portable equipment and its compatibility with removable line‑tape systems.

Quality Control Philosophy

Each board undergoes visual grading for knots, grain slope, and color variance; only boards with ≤5 % surface defects proceed to finishing.

Moisture content is verified with capacitance meters, targeting 6‑8 % ±1 % before packaging.

Finished panels are sampled for abrasion resistance and coefficient of friction, with results recorded in a traceable batch record.

Typical Technical Data

Custom dark maple hardwood sports flooring Company
Property Typical Value Test Standard
Density (kg/m³) 720 ASTM D4442
Janka Hardness (lbf) 1450 ASTM D143
Modulus of Elasticity (GPa) 1.9 ASTM D143
Vertical Deformation (mm) @ 500 N 2.5 EN 14904
Coefficient of Friction (dry) 0.60 ASTM D2047
Taber Abrasion (mg loss/1000 cycles) ≤80 ASTM D4060

Frequently Asked Questions

  • Can dimensions be customized? Yes – thickness, width, and length are tailored to project specifications; custom profiles require additional tooling lead time.
  • What information is needed for a quotation? Required details include court dimensions, subfloor type, desired finish, and any branding or line‑marking requirements.
  • Which grades of maple are available? We supply select‑grade (clear) and better‑grade (limited knots) dark maple; lower grades are not used for sports surfaces.
  • How is quality inspected before shipment? Each pallet undergoes moisture content verification, surface finish thickness measurement, and random abrasion testing per batch.
  • What packaging methods protect the flooring during transit? Boards are stacked with interleaving kraft paper, wrapped in stretch film, and placed in corrugated crates with corner protectors.
  • What is the typical production lead time? Standard lead time is 4‑6 weeks after receipt of approved shop drawings; expedited options are available upon request.
  • How are samples arranged? Sample kits (300 mm × 300 mm panels) can be shipped via express courier; charges are credited against the first order.

For technical datasheets, sample requests, or project‑specific quotations, please contact our engineering team.

Request Quote / Technical Info