Opening: 9:00-5:00

China Select Maple Hardwood Flooring Top Factory

China Select Maple Hardwood Flooring Top Factory
China Select Maple Hardwood Flooring Top Factory
China Select Maple Hardwood Flooring Top Factory

China Select Maple Hardwood Flooring Top Factory

Inquire

In stock

Select maple (Acer saccharum) harvested from managed plantations in northeastern China provides a uniform grain structure with minimal mineral streaks. The flooring is manufactured as engineered

Share this on:
China Select Maple Hardwood Flooring Top Factory

China Select Maple Hardwood Flooring Top Factory

Select Maple Hardwood Flooring – Technical Overview

Select maple (Acer saccharum) harvested from managed plantations in northeastern China provides a uniform grain structure with minimal mineral streaks.

The flooring is manufactured as engineered planks with a hardwood wear layer bonded to a cross‑laminated pine core, delivering dimensional stability under fluctuating humidity.

Key Material Properties

Typical specific gravity of the maple wear layer ranges from 0.68 to 0.72, corresponding to a Janka hardness of approximately 1,450 lbf.

Moisture content is kiln‑dried to 6‑8 % before lamination, reducing the risk of post‑installation cupping.

The wear layer thickness is available from 2 mm to 4 mm, allowing selection based on expected traffic intensity.

Typical Specifications

Property Typical Value Note
Total thickness 10 mm – 14 mm Customizable according to project requirements
Wear layer thickness 2 mm – 4 mm Affects wear resistance and refinishing potential
Plank width 120 mm – 200 mm Standard widths; narrow options available
Plank length 900 mm – 1800 mm Random lengths to minimize seams
Edge profile Micro‑bevel or square Selected based on installation method
Surface finish UV‑cured polyurethane, 30 % gloss Optional matte or satin finishes
China select maple hardwood flooring Top Factory

Dimensional Stability and Performance

The cross‑laminated pine core exhibits a linear expansion coefficient of approximately 0.0035 %/RH, limiting width change to under 0.2 % when relative humidity shifts between 30 % and 70 %.

With a wear layer hardness of 1,450 lbf, the surface resists indentation from typical industrial foot traffic and light equipment loads.

Acoustic testing shows a impact sound reduction of roughly 55 dB when installed over a 6 mm underlayment, meeting common office‑building requirements.

Applications in Industrial Environments

  • Showroom flooring where aesthetic consistency and low maintenance are critical.
  • Light‑assembly workstations requiring a stable substrate that resists rolling‑tool vibration.
  • Corridors and break‑room areas in manufacturing plants where spill resistance and easy cleaning are needed.
  • Retail‑front displays subject to frequent foot traffic but limited exposure to heavy machinery.

Quality Control Process

Each batch undergoes moisture‑content verification using pin‑type meters; boards outside the 6‑8 % range are redirected to re‑drying.

Visual grading follows the NHLA maple rules, separating clear, select and common categories based on knot size, grain deviation and mineral streaks.

Finished planks pass a 100 mm abrasion test (Taber) with a target wear index below 300 mg per 1000 cycles, ensuring surface durability.

Customization Options

  • Wear layer thickness from 2 mm to 4 mm in 0.5 mm increments.
  • Plank width adjustable between 100 mm and 250 mm to match layout modules.
  • Edge profiles: square, micro‑bevel, or eased edge for seamless integration with wall bases.
  • Surface finishes: matte (10 % gloss), satin (30 % gloss), or high‑gloss (60 % gloss) UV‑cured urethane.
  • Optional acoustic underlayment bonded to the underside for enhanced sound attenuation.

Packaging and Logistics

Planks are stacked in groups of four, separated by corrugated cardboard dividers, and unitized on heat‑treated pallets measuring 1.1 m × 1.1 m.

Each pallet is stretch‑wrapped with 80 µm polyethylene film and fitted with corner protectors to prevent edge damage during container handling.

Standard export packing includes a moisture‑barrier liner and desiccant packets to maintain equilibrium moisture content during transit.

Frequently Asked Questions

Can dimensions be customized?

Yes, total thickness, wear‑layer thickness, width and length can be adjusted according to project specifications; custom tooling may affect lead time.

What information is required before quotation?

Required details include desired wear‑layer thickness, plank dimensions, finish grade, quantity, delivery destination and any required certifications.

How is quality inspected?

Inspection combines moisture‑content testing, visual grading per NHLA, dimensional checks with calipers, and abrasion resistance testing on a sample set.

What packaging methods are available?

Standard palletized packing with stretch wrap and corner protectors; optional crate packing for high‑value or delicate shipments.

For technical data sheets, sample requests or project‑specific quotations, please contact our engineering team.