Opening: 9:00-5:00

China Grey Maple Hardwood Floors Manufacturer

China Grey Maple Hardwood Floors Manufacturer
China Grey Maple Hardwood Floors Manufacturer
China Grey Maple Hardwood Floors Manufacturer

China Grey Maple Hardwood Floors Manufacturer

Inquire

In stock

Grey maple originates from Acer saccharum subsp. leucoderme, a variant prized for its subtle silvery‑gray grain that emerges after steaming and drying. The species grows primarily in the northeastern

Share this on:
China Grey Maple Hardwood Floors Manufacturer

China Grey Maple Hardwood Floors Manufacturer

China Grey Maple Hardwood Floors Manufacturer

Grey maple originates from Acer saccharum subsp. leucoderme, a variant prized for its subtle silvery‑gray grain that emerges after steaming and drying. The species grows primarily in the northeastern provinces of China, where cold winters produce tight, uniform rings that enhance dimensional stability.

Material Characteristics

Typical air‑dried density ranges from 0.62 to 0.68 g/cm³, placing it between hard maple and oak. Janka hardness measures around 1,450 N, providing resistance to indentation comparable to European beech. After kiln drying to 8 % ± 2 % moisture content, the board exhibits minimal seasonal movement.

Manufacturing Process

Logs are first sawn into cants, then graded for knot frequency and grain angle before entering a low‑temperature kiln. Subsequent planing achieves a thickness tolerance of ±0.1 mm, while profiling machines cut tongue‑and‑groove or click‑lock edges with a repeatability of 0.05 mm. A UV‑cured acrylic finish is applied in three coats, delivering a wear layer of 0.35 mm.

Dimensional Stability & Performance

With a tangential shrinkage coefficient of 0.18 % and radial coefficient of 0.10 %, grey maple shows less than 0.3 % dimensional change across a 30 % to 70 % relative humidity swing. The finished surface achieves a Taber abrasion index of ≤80 mg loss after 1,000 cycles, suitable for moderate‑traffic commercial zones.

Applications

  • Open‑plan offices benefit from the floor’s low acoustic reflectance and consistent colour under LED lighting.
  • Retail boutiques choose the subtle grey tone to complement neutral palettes while maintaining scratch resistance from foot traffic and display fixtures.
  • Hospitality lobbies utilize the material’s resistance to rolling luggage loads, thanks to its high modulus of elasticity (~12 GPa).
  • Educational institutions value the low VOC finish, meeting indoor air quality standards for classrooms and libraries.
  • Healthcare corridors require surfaces that tolerate frequent disinfectant wiping; the sealed acrylic coat resists chemical degradation.

Customization Options

Board width can be specified from 90 mm to 220 mm in 10 mm increments, while lengths range from 300 mm to 2,400 mm. Thickness options include 12 mm, 15 mm, and 18 mm core with a 0.35 mm wear layer. Edge profiles available are square, 2‑mm bevel, and micro‑bevel. Finish sheen levels span matte (10 % gloss), satin (35 % gloss), and gloss (70 % gloss). Stain intensity can be adjusted from light grey to deep charcoal upon request.

Quality Control & Inspection

Each batch undergoes moisture‑content verification using capacitance meters, with acceptance limits of 6 %–10 %. Hardness is spot‑tested via Shore D, targeting 80 ± 5. Dimensional checks are performed on a coordinate measuring machine, verifying width, length, and thickness tolerances. Finish adhesion is assessed by cross‑hatch tape test, requiring a rating of 5B or better per ASTM D3359.

Packaging & Shipping

Boards are stacked on fumigated wooden pallets, separated by layers of polyethylene sheeting to prevent moisture transfer. Corner protectors and edge straps secure the load, while the entire pallet is wrapped in UV‑stretch film. For ocean freight, pallets are placed in 20‑ft or 40‑ft containers with desiccant bags and secured with friction‑type dunnage to limit movement during transit.

Typical Values

China grey maple hardwood floors Manufacturer
Property Typical Value Unit Notes
Density (air‑dry) 0.62‑0.68 g/cm³ Variation with growth region
Janka Hardness 1,450 N Average of radial & tangential
Moisture Content (KD) 8 ± 2 % Target for shipment
Tangential Shrinkage 0.18 %/ %RH At 30‑70 % RH
Wear Layer Thickness 0.35 mm UV‑cured acrylic
Taber Abrasion (CS‑10) ≤80 mg loss/1000 cycles Standard load 1 kg

FAQ

Can board dimensions be customized?

Yes, width, length, and thickness are adjustable per project specifications; custom tooling may apply for non‑standard sizes.

What information is required before quotation?

Required details include desired dimensions, finish sheen, edge profile, quantity, delivery destination, and any special packaging needs.

What materials are available besides grey maple?

We also supply natural maple, white oak, and walnut; each can be finished to a grey tone upon request.

How is quality inspected?

Inspection covers moisture content, hardness, dimensional tolerance, finish adhesion, and visual grading; reports are available on request.

What packaging methods are available?

Standard palletized packaging with polyethylene interlayers, corner protectors, and stretch film; custom crating or container‑loading options exist.

How are export shipments protected?

Shipments include desiccant bags, moisture‑barrier wrapping, and friction dunnage to minimize movement and humidity ingress during transit.

What is the typical production lead time?

Lead time ranges from 20 to 35 working days depending on order complexity and current capacity; exact timing is confirmed at quotation.

How are samples arranged?

Sample boxes containing three boards each are shipped via express courier; charges are credited toward a subsequent order.

Contact / CTA

For technical data sheets, sample requests, or project‑specific inquiries, please reach out to our sales engineering team.

Submit Inquiry